restdream.blogg.se - Logger pro 3.12 updates

LOGGER PRO 3.12 UPDATES HOW TO
LOGGER PRO 3.12 UPDATES SERIAL
LOGGER PRO 3.12 UPDATES UPDATE
LOGGER PRO 3.12 UPDATES UPGRADE

Improved reliability of sending emails over slow connections (i.e., BGAN M2M).Added support for Symphonie iPackGPS | LTE-VZW and Symphonie iPackGPS | LTE-ATT (hardware coming soon).Improved support for LTE iPackGPS models (hardware coming soon).Recommended for BGAN M2M and LTE iPackGPS users.** Added support for LTE-TDD iPackGPS model.Extended connection retry time from 10 minutes to 60 minutes for LTE-VZW iPackGPS only to improve interaction with Verizon network.Resolves issue where channel sample rate could be erroneously set to zero.Adds min and max statistics to Modbus data for wind vanes.Adds support for unknown (i.e., unreleased) P-SCM types.Adds support for 9410 P-SCM (0 to 5V SE Input, Constant 5V Exc).Resolved issue with SD card showing “E” instead of “F” when full under certain conditions.Resolves an issue seen in a small number of SymphoniePRO loggers where one or more anemometer channels drop out due to an unexpected configuration state change.Extended wind vane support (on all analog channels, with additional configuration data).44031 10K NTC Thermistor type temperature sensors.Updated channel configuration to support additional sensors, including:.Updates *.RLD file closure routine around logger reset events.Updates *.RLD file handling to prevent automated delivery of invalid files.

LOGGER PRO 3.12 UPDATES SERIAL

Adds capability to use Modbus RTU serial sensors on COM-A and COM-B serial ports (Note: Hukseflux SR30 support included contact NRG to request support for new device models).

**Note: Loggers updated to this version cannot be downgraded to prior versions.**

Resolves several Logger LCD screen bugs.

Resolves issue with counter channels 5, 6, and 7 encountered in small number of loggers (ref.

Updates Direct Normal Irradiance (DNI) Calculation option to enable sourcing GHI and DHI from separate sensors.

Resolves issue with time stamps on calculated statistical values in Modbus data.

Resolves issue in Modbus data where logger and site information values are zeroes.

Improves power management by increasing low voltage limit for iPack battery from 10.5 V to 11.5 V.

Adds zero crossing math for serial devices with signed signals (e.g., SR30 body temp).

Adds support for floating point values from serial devices (e.g., MS-80S).

Adds support for 9420 P-SCM | 0 to 5 V, Diff Input, Const 15 uA, No EXC, 2/4w.

Adds support for NRG PVT1 PV Temperature Sensor.

LOGGER PRO 3.12 UPDATES UPDATE

Resolves issue with iPack restarting after firmware update related to a false low battery indication.Resolves issue with GPS coordinates that could appear when "Lock Location" setting is active and logger is re-located.Adds support for selecting serial channels in DNI calculated channel setup.Adds support for LTE-G iPack models (hardware coming soon).Resolves issue with iPack boot sequence timing for iPackACCESS | LTE-G model.Adds support for Daily Insolation calculated channel.Resolves issue with scaling of serial inputs to Albedo and Ratio calculations.*General release recommended for solar resource measurement applications. Adds support for Daily Sum (precipitation) calculated channel - Resolves issue where serial and calculated channel configuration can be reset using keypad right arrow during LCD wakeup.Adds support for Daily Sum (precipitation) calculated channel.

LOGGER PRO 3.12 UPDATES UPGRADE

*General release NRG Systems recommends users upgrade all loggers to this version.

LOGGER PRO 3.12 UPDATES HOW TO

For questions on how to administer firmware upgrades, please contact our tech services team at RELEASE NOTEs Version 3.4.4*, With SymphoniePRO, these firmware upgrades can be done either locally with a USB-connected PC or remotely via MetLink. While software upgrades are conducted right on your PC, firmware upgrades need to be administered directly to the SymphoniePRO Data Logger and iPack devices.